Cobra Magnum Rear Loader

The New Way Cobra Magnum offers a high compaction body at a lighter weight than the competition. Add in a huge 3.55 yd³ hopper and a striking 21-23 second cycle time and the Cobra Magnum delivers a crushing bite to anything you throw at it.The Cobra Magnum Rear Loader

  • General Specs
  • Hydraulic Cylinder Specs
  • Chassis Min Requirements
General Specifications (standard)
Model
20 RL
25 RL
27 RL
32 RL
Body Capacity
20 yd³
25 yd³
27 yd³
32 yd³
Body Width - Outside (A)
96"
96"
96"
96"
Body Width - Inside
87"
87"
87"
87"
Body Length (B)
251.5"
289"
301"
315.5"
Body Length - Tailgate Raised
289.5"
327"
339"
353.5"
Body Height (C)
102.5"
102.5"
102.5"
102.5"
Body Height - Tailgate Raised
187"
187"
187"
187"
Approx. Body Weight *
 (Empty & Exclusive of Options)
14,880 lbs
15,250 lbs
15,400 lbs
16,550 lbs
Hopper Capacity
3.55 yd³
3.55 yd³
3.55 yd³
3.55 yd³
Hopper Opening Width
80"
80"
80"
80"
Loading Sill Height
3.5" below frame
3.5" below frame
3.5" below frame
3.5" below frame
Hopper Cycle Time (sec)
25-28
25-28
25-28
25-28
Trough (Y/N)
N
N
N
N
Hydraulic Cylinder Specifications (standard)
Model
20 RL
25 RL
27 RL
32 RL
Slide Cylinders (2)
5" Bore, 38.63 Stroke, 4" Rod
5" Bore, 38.63 Stroke, 4" Rod
5" Bore, 38.63 Stroke, 4" Rod
5" Bore, 38.63 Stroke, 4" Rod
Sweep Cylinders (2)
4.5" Bore, 25.63" Stroke, 3.5" Rod
4.5" Bore, 25.63" Stroke, 3.5" Rod
4.5" Bore, 25.63" Stroke, 3.5" Rod
4.5" Bore, 25.63" Stroke, 3.5" Rod
Tailgate Cylinders (2)
3.5" Bore, 42" Stoke, 2" Rod
3.5" Bore, 42" Stoke, 2" Rod
3.5" Bore, 42" Stoke, 2" Rod
3.5" Bore, 42" Stoke, 2" Rod
Ejection Cylinder
4 Stage, 7.5" Bore of largest Stage, 96.5" Stroke
4 Stage, 7.5" Bore of largest Stage, 118" Stroke
4 Stage, 7.5"
4 Stage, 7.5" Bore of largest Stage, 160" Stroke
Chassis Minimum Requirements (standard)
Model
20 RL
25 RL
27 RL
32 RL
Minimum GVWR **
56,000 lbs.
60,000 lbs.
62,000 lbs.
64,000 lbs.
Recommended Cab
138"
160"
172"
204"

- Length measured depends on options ordered
*
- Approximate Body Weight empty and exclusive of options
** - Any Chassis sent to Scranton Manufacturing with less than the minimum guideline requirements will not be mounted. (Chassis must be capable of carrying the net weight of the body plus the weight of the refuse collected.)

King Cobra Technical Drawing

Cobra Magnum Body Construction


Body Specs
Main Body Rails 8"x3"x1/4"   Structural Tube
Floor Front: 10ga; Rear: 7ga   Front: 50K; Rear: 100K
Floor Braces 8" Wide; 10GA   50K
Center Floor Braces 8" Wide; 10GA   50K
Mounting Brackets Welded to main body rails; 1/2"   A36
Ejection Panel Tracks 8" Formed Channel 7GA; Wear Strips: 1/2"x3   50K; A36
Side Walls 10GA   80K
Roof Front: 7GA; Rear: 10GA   Front: 50K; Rear: 80K
Rear Frame Formed 10"X7" Channel 7GA; Formed Rear Hinge Cross Beam 1/4"x3x10   A36; 50K
Rear Frame Lower Slope 1/4"   80K
Rear Frame Lower Slope Supports Formed 6"x4" Channel 7GA   50K
Rear Slope Perimeter Support 1/2"x5"   A36
Tailgate Hinge Lugs 1/2"   A36
Upper Bulkhead 10GA   80K
Side Bulkhead 1/4"   50K
Lower Bulkhead 7GA   50K
Access Door 30"x30"    
Upper Body Bolsters (Transitions) 7GA   36K
Lower Body Bolsters (Transitions) 12GA   36K
Tailgate Specs
Hopper Capacity 3.55yd³    
Hopper Opening Height 50"    
Hopper Opening Width 80"    
Upper Hopper Brace 1/4"   80K
Hopper Floor 1/4"   T1 (100K min)
Hopper Braces 1/4"   50K
Tailgate Seal Height 50"    
Lower Tailgate Side 1/4"   T1 (100K min)
Upper Tailgate Sides Upper: 10GA; Lower: 7GA"   Upper: 50K; Lower: 100K
Slide Tracks Formed 1/4"   50K
Slide Wear Strips 1/2"x3   A36
Tailgate Side Braces 10GA   50K
Tailgate Hinge Lugs 1-1/2"   50K
Slide Specs
Face Sheet 7GA   T1 (min)
Face Sheet Braces 10GA   50K
Lugs 1/2"   50K
Lug Center Braces 1/4"   50K
Upper Slide Shoe Tube: 3"x5"x3/8"; Shoe: 4"x20"x1"   Tube: A500 GRD-B; Shoe: UHMW
Lower Slide Shoe Tube: 3"x5"x3/8"; Shoe: 4"x13"x1"   Tube: A500 GRD-B; Shoe: UHMW
Upper Slide Cylinder Pins 2-1/2" OD   1045CD
Upper Sweep Pin 2" OD   1144 Stressproof
Lower Sweep Pin 3" OD   1045CD
Sweep Specs
Face Plate 1/4"   100K
Lugs 3/4"   50K
Center Braces 1/4"   A36
Backing Plate 1/4"   50K
Sweep Nose 5/8"   A36
Bronze Bushings 3"   ID
Ejection Panel Specs
Base & Support Structure Base-3"x3"x1/4" Structural Steel Tubing; 1/4"   A36 Formed & Integrated upright supports
Upper Face Sheet None    
Face Sheet 10GA   80K
Shoes 4"x53-1/2"x1"   UHMW
Nose 1/2"   A36
Cylinder Supports Integrated into upright supports    
Cylinder Pin 3" OD   1144 Stressproof
Hydraulic System Specs
Oil Reservoir 50 Gal with 100 Mesh 141 Micron Suction Strainer 227 L
Oil Flow w/Std. Pump 36 GPM 1,000-1,200 RPM
Operating Pressure 2,750 PSI 16,892 KPA
Hydraulic Hoses 4 to 1 Burst  
Return Filter 10 micron  
Engine RPM 1,275 - 1,550  

Standard Equipment

  • Semi Automatic Cycling
  • Auto Back Pack
  • Accelerator Kit
  • Turn Buckle Locks
  • Back Up Alarm
  • Light Bar
  • All LED Lights
  • Sight Gauge on Oil Tank
  • Oil Pressure Gauge
  • Chrome Rod Cylinders
  • Side Access Door
  • Driver Alert Buzzer
  • Tailgate Ajar Indicator
  • Bolt on Steps on Rear
  • Prime Paint
  • Rear Vision Camera System
  • Talamar Extreme Hydraulic Fluid

Optional Equipment

  • Special Lighting
  • PTO & Pump
  • Finish Paint-Imron 5000
  • Container Lifts (commercial & residential)
  • Body Scale System
  • Auto Tailgate Locks
  • Steel Upgrades
  • Extended Warranties